Category Archives: Side Bead Planes

Side Bead Planes now in Store

We currently have a restock of improved side bead planes in the store.  These are available in bead sizes of 1/8″, 3/16″, and 1/4″.  It should be mentioned that our sizing is a measurement of the bead itself, and that the actual profile, including the quirk, is about 1/32″ wider than the bead size.  Thus the 1/8 is 5/32″ wide, the 3/16 is 7/32″, and the 1/4 is 9/32″.  More information about the side beads can be found here.

From left 1/8″, 3/16″, and 1/4″

Taking Orders for Side Beads

We are currently taking orders for side bead planes, the construction of which are now under way.  These will be offered in three sizes:  1/8″, 3/16″. and 1/4″.  Constructed of quarter sawn American Beech, with tapered O-1 tool steel irons, each plane is sharpened and test cut, and is ready to go right out of the box.  Expected delivery will be approximately the end of April.  Price is $275 each, plus shipping.  If interested, contact us and we will reserve any sizes you wish.  Payment will be due upon completion.  Quantities are limited to 8 planes in each size.

For more information about our side beads, click here.

Heels are stamped with sizes

Side Bead Planes

Side beads, or beading planes, are used to put a bead along the edge of a board, and can be used in many situations, such as back boards, the bottom of table aprons, or along shelf fronts. A very versatile plane, these were, along with hollow and rounds, perhaps the most common molding plane produced.  These are one of the easiest molding planes to use, with an integral fence and depth stop, and no spring.  (The plane is held vertically.)   Simply hold the plane against the edge of the stock being profiled, and make passes until the depth stop prevents any further cutting.  For a different treatment, running the plane along two sides of a corner will produce a 3/4 bead on that corner.

Our planes are made of  quarter sawn American Beech.  The tapered O-1 tool steel iron is bedded at 55 Degrees for use in hardwoods, and is sharp and ready to use.  The bead is boxed with persimmon, which is cut with the grain on a bias to match the bed, to ensure a long tool life.  We produce these planes in 1/8″, 3/16″ and 1/4″ beads, the most common and useful for furniture use.   It should be mentioned that our sizing is a measurement of the bead itself, and that the actual profile, including the quirk, is about 1/32″ wider than the bead size.  Thus the 1/8 is 5/32″ wide, the 3/16 is 7/32″, and the 1/4 is 9/32″.

Finish is Minwax Antique Oil Varnish, with a coat of paste wax added for a smooth even sheen and inviting feel.

Side bead planes in, from left, 1/8′,   3/16″ and   1/4″ sizes.

After the initial run of these planes, some refinements were made.  The wedges now graduate in size from 5/32″ to 7/32″.  This makes the planes have a more uniform appearance, but more importantly, they are narrower in width in the grip, which makes them lighter and lowers the center of gravity.  Easier to use with better feel and less fatigue  are the end result.

Price is $275 per plane.  Each is sharpened and test cut before shipping, making them ready to go right out of the box.  Currently, the 1/4″ size is available here.

 

Graduated wedge sizes are apparent in this view.

 

Heels are stamped with sizes.

 

Planes are 10″ long with a 55 degree bed angle.  Note the chamfer at the escapement, which makes it easier to locate the iron against the blind side when setting up.

 

Beads cut with all three sizes of beading planes.